APPAREILS D'ANALYSES DES PACKAGINGS BOUTEILLES BOITES ET AEROSOLS

AT2E propose désormais une nouvelle gamme d'appareils de mesures dimensionelles, d'essais de résistance et d'analyses des packaging : VERRE - PET - ALUMINIUM - BOITES - BOUTEILLES - PACK - AUTRES

Ces appareils présententun très bon rapport qualité prix. Consultez nous !

APPAREILS D'ANALYSES POUR LES BOUTEILLES (Verre et PET ) ET PREFORMES

PET-AXL-100 PET Bottle Axial Load Tester

 

Le "AXL-100 " mesure la résistance force axiale des bouteilles en Newton. La bouteille est placée dans un support et peu à peu forcée vers le haut contre la plaque de pression. L'espace entre le support et la plaque supérieure peut être modifié avec des entretoises. Le système peut se stopper après que le pic de force a été appliquée, charge maximale à laquelle la bouteille est capable de résister. La valeur maximale peut maintenant être lue à l'écran

• Industie Standard 
• Platines parfaitement parallèles 
• Auto enregistrement et affichage la force de la valeur de crête 
• Écran tactile PLC controleur
• Stable processus de pressage, les données collectées automatiquement par le micro-ordinateur

• plaque de pression d'auto reset après l'essai est terminé. Facilité de mise en place des échantillons. 
• Affiche le max. et min. mesure la valeur moyenne après plusieurs tests. 
• Applicable pour des échantillons de différentes dimensions. 
• Protection contre les surcharges mécaniques

Données techniques:  
Gamme de mesure: 500 N  
Résolution: 0.1N  
Panneau arrière: RS232  
Alimentation: 240VAC 50-60Hz  
Dimensions: 500 mm x 400 mm x 600 mm (L x P x H)  
Poids: 67 kg

PEBT-2 PET BURST TESTEUR

• méthodes de tests   Internationales couramment utilisées
• Écran tactile, affichage de l'heure d'essai et de pression réelle

"PEBT-2 PET Testeur Pression bouteille " est un équipement d'essai spécialisé pour tester les bouteilles PET ou bidons. Il a été conçu en conformité avec les trois organisations internationales des méthodes d'essai communément utilisées, les utilisateurs peuvent choisir la méthode d'essai en fonction de leur exigence. Le PEBT-2 est capable de tester les capacités de résistance sous une certaine pression ou l'essai de rupture.

Par le biais de la reconstitution de pressurisation, le processus de pressurisation a été linéarisé, et augmente jusqu'à atteindre le point de consigne ou point d'éclatement

Après la sélection du programme de tests, PEBT-2 sera lancé automatiquement selon les paramètres. L'écran tactile affiche la valeur de pression en temps réel et d'enregistre la pression maxi et la pression d'éclatement.

Données techniques (Sous réserve de modifications):

• Gamme de mesure: 0 - 2 MPa (290Psi)  
• Résolution: 0.01Mpa  
• Max. capacité de l'échantillon: 3 L  
• Alimentation: 115/230V, 50 - 60Hz  
• Panneau arrière: Sortie série RS232  
• Dimension: 830 × 580 × 1600mm (LxPxH)  
• Poids: 120 kg

BPT-2 Testeur de pression bouteille verre

Le "BPT-2 " est un instrument de test pour les résistances à la pression des récipients en verre. Essai de pression à un point de pression prédéfini (essais preuve) ou à la destruction. La BPT-2 est conçu pour favoriser la facilité d'exploitation et d'entretien, et est pleinement conforme aux exigences de l'essai international.

• Description technique :
• Standard Industrie *
• * Verrous de sécurité sur les portes de la chambre d'essai
• * application de la pression selon les exigences
• * Conception durable et solide
• * Système de contrôle de programme (PLC)
• * Écran LCD tactile
• * R- 232 C
• * Affiche le max. et min. mesurer la valeur moyenne et après plusieurs tests.

• Données techniques (Sous réserve de modifications):
• Gamme de mesure: 0-57bar
• Résolution: 0,1 bar
• Montée enpression : 0.4MPa/Sec
• Panneau arrière: Sortie RS232 de série
• Alimentation: 115 V / 230 V, 50-60Hz
• Dimensions: 830mm × 580mm × 1600mm (L x P x H)
• Poids: 120 kg

FGJ Appareil a sertir les capsules couronnes ( CROWN )

Le "FGJ " permet de sertir les capsules couronnes sur les bouteilles en verre. Pour le vin, la bière, les boissons gazeuses.

volume de la bouteille: 250ml 375ml 500ml 640ml

 

 

 

 

VAT-300

Appareil de mesure de la perpendicularité des bouteilles ( auto )

Le "VAT-300 permet de mesurer l'écart de perpendicularité des bouteilles en verre. Avec le processeur de données, le VAT-300 est capable de collecter les données de mesure de l'indicateur numérique Mitutoyo et montrer les résultats automatiquement.

Données techniques:  
diamètre de l'échantillon: max. 120 mm (plus grande, par ordonnance)  
Gamme de mesure: 0-10mm  
Résolution: 0,01 mm  
Dimensions: L280 x W180 x H 380 mm  
Poids: 12,5 kg

PEPT-100

Appareil de mesure de la perpendicularité des bouteilles PET(Digital)

Testeur de bouteille PET qui est équipé du lecteur Mitutoyo numérique est utilisé pour mesurer la perpendicularité de la bouteille PET.

Données techniques:  
gamme de l'échantillon: 90 mm (autres diamètres peuvent être faits sur mesure)  
Plage de mesure: 0-10mm  
Précision: 0.01 mm  
Dimension: L350 x W250 x H 370 mm  
Poids net: 12,5 kg

PETG-200

Appareil de mesure de l'épaisseur des preformes PET ( digital )

 

PETG-200 Mesure l'épaisseur des préformes de bouteille PET.  
manutention de conception simple et mesure la variation permettant à l'opérateur d'obtenir le résultat exact de mesurer facilement.  
Cette jauge est constituée de la pince de mesure Mitutoyo.  
Données techniques:  
Gamme de mesure: 0-10mm  
Précision: 0.001mm

PETG-100

Appareil de mesure de l'épaisseur des preformes PET ( analogique )

PETG-200 Mesure l'épaisseur des préformes de bouteille PET.  
manutention de conception simple et mesure la variation permettant à l'opérateur d'obtenir le résultat exact de mesurer facilement.  
Cette jauge est constituée de la pince de mesure Mitutoyo.  
Données techniques:  
Gamme de mesure: 0-10mm  
Précision: 0.02mm

POLARISCOPE

Le polariscope permet de bien détecter le défaut d'injection et de moulage sur la préforme  
Nous vous conseillons de choisir la liste de défauts pour prefrom et polariscope en même temps

 

 

 

HOT WIRE CUTTER

 

Le HWC permet de couper en trois parties les bouteilles PET pour permettre de mesurer la répartition des matières après soufflage des bouteilles

 

 

 

 

AUTRES APPAREILS : ANALYSES DES AEROSOLS

ABT-200 Burst Buckling Tester for aerosol cans

 

“ ABT- 2 00 Burst Buckling Tester for Aerosol Cans” is used for testing the buckle value of bottom and end (dome) of aerosol cans and the pressure at which the can bursts.

The ABT-200 was PLC controlled, and equip with the special designed clamp device, ABT-200 is able to test the buckle value of free ends (dome) or bottom of aerosol cans independently.

The professional analyzing software of ABT-200 is able to display the pressure curve, monitor and record three buckle values: end buckle value, bottom buckle value and burst value. The database system manages the measurement result and curve, and the system will carry out the testing process automatically, so that no manual operation needed during the testing process.

Technical data:
Pneumatic supply: 0.5Mpa
Testing pressure: 0-4Mpa
Graduation: 0.01Mpa
Dimension : 555 x 400 x 860 mm (L X W X H)
Weight: 50kg
Sample type: All types of aerosol cans

APPAREILS D'ANALYSES POUR LES BOITES - CANNETTES

AXL-4000   Testeur de charge axiale  

Le "AXL-4000 " mesure la résistance force axiale de canettes en Newton. La boîte est placée dans un support et peu à peu forcée vers le haut contre la plaque de pression. L'espace entre le support et la plaque supérieure peut être modifié avec des entretoises. Le système peut se stopper après que le pic de force a été appliquée, charge maximale à laquelle la boîte est capable de résister. La valeur maximale peut maintenant être lue à l'écran

• Industie Standard 
• Platines parfaitement parallèles 
• Auto enregistrement et affichage la force de la valeur de crête 
• Écran tactile PLC controleur
• Stable processus de pressage, les données collectées automatiquement par le micro-ordinateur

• plaque de pression d'auto reset après l'essai est terminé. Facilité de mise en place des échantillons. 
• Affiche le max. et min. mesure la valeur moyenne après plusieurs tests. 
• Applicable pour des échantillons de différentes dimensions. 
• Protection contre les surcharges mécaniques

Données techniques:  
Gamme de mesure: 3000 N  
Résolution: 1N  
Panneau arrière: RS232  
Alimentation: 240VAC 50-60Hz  
Dimensions: 500 mm x 400 mm x 600 mm (L x P x H)  
Poids: 50 kg

BDG-100 Jauge de profondeur pour fond de boite

 

BDG-100 est une jauge numérique pour la mesure des paramètres à la profondeur du fond des boîtes de boisson. Avec le Mitutoyo 0.01mm

indicateur numérique Mitutoyo type SPC Sortie des données 
facile à lire 

Ne n écessite pas de formation et est extrêmement facile à l'utiliser 
de données techniques: 
Résolution: 0, 01 mm

CBT-100 Testeur de bombage des capots

 

Le CBT-100 Boucle Testeur pour les canettes, détermine la pression exacte à laquelle les fonds peuvent résister avant de "bomber le dôme ".

Le capot de boite ou plat se place dans le support. Après fermeture de l'appareil avec un capot en plexiglas. La boîte est scellée avec une structure : joint torique en caoutchouc. La pression augmentate jusqu'à 5 bar (programmable), la vitesse de mise en pression peut-être règlée. Le test prend fin dès que les boucles lachent. La valeur de pression maximale est indiquée à l'écran.

Tout les formats peuvent être testés, les inserts sont disponibles et peuvent être échangées en quelques secondes.

• Industrie Standard  
• Utilisable pour les boîtes et les parois plates  
• RS 232C
• Sortie des données, transfert des données au PLC  
• Écran tactile / système PLC,données collectées automatiquement.  
• La vitesse est réglable et le courbe de pression peut être réglée  
• Haute précision  
• Test Point d'étalonnage  
• Affiche le max. et min. mesure la valeur moyenne après plusieurs tests  
• Conception sécurisée  
• Protection contre les surcharges  

D onnées techniques:  
Plage de mesure: 0-900 Kpa (0.9Mpa)  
Résolution: 1 KPa  
Panneau arrière: RS 232C  
Alimentation: 230V/50Hz  
Alimentation pneumatique: 1,0 MPa  
Dimensions: 600 x 450 x 430 mm  
Poids: 40kg

CHG-d Digital Can Height Gauge

 

The CHG-d Digital Can Height Gauge can be used to measure the height of beverage, food, and aerosol cans. Constant measuring force for accurate, repeatable, user-independent results. With the Mitutoyo 0.01mm Resolution Digital Indicator. If you purchase the adapter and cable, the instrument can communicate with a computer.

Option Calibration piece: 60mm ; 88.4mm ; 111.2mm ; 115.2mm ; 134mm ; 168mm ; etc

Technical data (changes reserved):
Resolution: 0.01 mm
Accuracy: 0, 02 mm
Tailor-made Digital Can Height Gauge for Straight Wall Cans

CMD-200 Can Measure Desk for Rear Stations

 

CMD-200 Can Measure Desk for Rear Stations is developed on basis of the long experience of Rear stations in 2 piece can product line.

 

CMD-200 Measure Flange width , Bottom depth, can height, Internal Diameter. It is equipped with Mitutoyo 0.01mm Resolution Digital Indicator, If you purchase the multiplexer and cable, the instrument can communicate with SPC system or a computer.

Technical data:
Resolution: 0.01mm

FWG-100-d ? FWG-200-d ? FWG-300-d

Flange Width Gauge

FWG-100-d FWG-200-d ? FWG-300-d

The “FWG-100-d Flange width gauges” is designed to measure the flange width of open ended cans. The spring loaded can guides automatically position the can for fast, accurate, and repeatable measurements. Constructed of machined for corrosion resistance and long life.  The base plate is stainless steel to extend the wear life of the surface. With the Mitutoyo 0.01mm Resolution Digital Indicator. The gauges may be connected to a computer via a multiplexer.

Technical data (changes reserved):
Resolution: 0, 01 mm

Sample Capacity
FWG-100-d: 50 -90mm dia.
FWG-200-d: 50 -200mm dia.
FWG-300-d: 50 -300mm dia.
Bigger by order

IDG-100 // IDG-200

Can Internal Diameter Gauge  

 

 

This unit serves for quickly checking the Internal Diameter of can. It is equipped with a calibration piece.
IDG-100 is for small diameter cans ; Cans dia. 52 -100 mm (only measure one type can),
IDG-200 is for big diameter cans; Cans dia. :80 -260 mm (only measure one type can)
One type cans must equip with one calibration pieces and one set of measure blocks (change parts).
If you must measure several type cans, you can order several pcs of IDG-100 or IDG-200.
Or you can order several psc of calibration pieces and several sets of measure blocks.
It is equipped with a digital dial gauge with "reset" and "preset" function, LCD display and data outlet for connecting the unit to a computer via multiplexer, if required.

Technical data:
Resolution: 0, 01 mm
Power supply: Battery , SR-44, approx.5.000 h
Accuracy: 0.01mm

SLG-d Seam Length Gauge

 

The SLG-d Seam length gauge can be used to measure Seam length (Seam height).

Can is positoned by standing up during measuring. With the Mitutoyo 0.01mm Resolution Digital Indicator. If you purchase the adapter and cable, the instrument can communicate with a computer.
Technical data:
Measurement range: 0 -7mm
Resolution: 0.01mm

STG-200-d Seam Thickness Gauge (Digital)

 

The STG-200-d Seam thickness gauge can be used to measure Seam thickness. With measure angle compensation. The center measure point can be adjusted. Cans can be auto - positioned in the center easily during measuring. With the Mitutoyo 0.01mm Resolution Digital Indicator.

If you purchase the adapter and cable, the instrument can communicate with a computer.
Technical data:
Measurement range: 0 -6mm (other measure range could be customized)
Resolution: 0.01mm

>STR-100 Seam Stripper

The automatic “STR-100 Seam Stripper” is a sensible, affordable, teardown method to prepare the double seam teardown analysis. One fast, safe teardown operation without damaging or distorting the cover hook. Reduce teardown time for more frequent inspections. Tooling quick change in few seconds. Models are available for most common can sizes of beverage, food, and aerosol cans. When ordering, the end diameter and can height must be specified so that the appropriate change parts are included. Efficient cut and strip both aluminium and steel cans in a single motion. 10 seconds per can. Eliminates the repetitious actions by hand.

An important part of any seam evaluation is the actual teardown of the can seam to determine tightness or wrinkle rating.

 

 

 

 

 

WTG-100 Wall Thickness Gauge for Trimmed 2-Piece Cans

Measure Topwall Thickness and Midwall Thickness with this gauge for Trimmed 2-Piece Cans.

Available for any Trimmed 2-Piece Cans of any height, the Wall Thickness Gauge measures topwall and midwall thickness. The digital dial indicators measure to 0,001 mm (0.00005) resolution.
Mitutoyo Standard SPC Data Output
Easy to read digital display
Requires little training and is extremely easy touse
Technical data (changes reserved):
Resolution: 0.001 mm
Accuracy: 0, 01 mm

BDD-200 Bead Depth Gauge (Digital)

BDD-200 Bead Depth Gauge is for measuring the bead depth of the can body.

BDD-200 has the fine designed can holder, which ensures the cans keep still during the measuring, and the results are more accuracy.

To purchase the data processor, it is able to collect the readings from the indicator and calculate the bead depth automatically. Or to purchase the transmitter and cable, it is able to transfer the data to computer or SPC system, so that to avoid the rates of man-made mistake.

Technical data:
Measure range: 0 -10mm (change by order)
Graduation: 0.01mm

CSS-300 Seam Saw

--- Applicable for all can types, especially for large paint cans, rectangle cans

 

 

“CSS-300 Seam saw” is a special seam circular saw with double cut for double seam inspections. The CSS 300 has specially designed for the irregular shaped can s, like rectangle cans, oval cans, etc. Also aerosol-cans can also be sawed with the saw. The nitrated blades achieve together with the speed of approx. 1.000 r/min. so that comes a very plain cut surface. The seam image on the Canneed series of Automatic Seam Monitors gets thereby very clear and improves measurement speed and reliability.

Technical data (changes reserved):
Sample can dia. : 45 -360mm (bigger by order)
Sample type : 2 piece cans, 3 piece cans, and aerosol cans
Saw blades: 100 x 22 x 0, 5 mm (also available with 80 x 22 x 0, 5 mm )
Speed: approx. 1.000 r/min.
Power supply: 220 V
Power: 100 W
Dimensions: L420 × W320 × H 150mm
Weight: 30kg

CSS-200 Seam Saw

“CSS-200 Seam saw” is a special seam circular saw with double cut for double seam inspections. The CSS 200 was specially designed for 2- and 3-piece can s. Also aerosol-cans may be sawed with this saw. The nitrated blades achieve together with the speed of approx. 1.000 r/min. a very plain cut surface. The seam image on Caneed series Automatic Seam Computer (Video Seam Monitors), and automatic seam measuring systems gets thereby very clear and improves measurement speed and reliability.

Safety design: In front of the saw blade, there was a proximity sensor, if the non-metal material get close above the sensor, the saw will not start even if the power switch is on, so that to minimize the accidents caused by the faulty operation or carelessness.

VRM 3A Video Rivet monitor

--- rivet quality of the ends

Familiar Defect of Rivet

Normal	Crinkle
Crack	Off the ring

The “ VRM 3A Video Rivet monitor“ is a Video camera system to observe and evaluate the rivet profile images of ends. Any end of varying diameter may be tested . The end is cut through the rivet by the low speed saw, the rivet is positioned manually in front of the camera. The rivet profile images display on the display. The “ VRM 3A Video Rivet monitor“ can be used with monitor to just observe and evaluate the rivet profile images. The “ VRM 3A Video Rivet monitor“ also can be used with a PC to be a compact measuring system. Within VRM image archive software the computer offers a measurement. This may be stored in computer or printed out on a laserprinter.

CAN-1050 Can Closing Force Gauge

 

“CAN-1050 Can Closing Force Gauge” is for measuring the force of seaming head of the seaming machine. Advantages:

•  Deduct the scrap rate of the production
•  Shorten the adjusting time, improved production efficiency.
•  Improved the seam quality
Technical data:
Measure range: 25 -500 lbs . / 10-230 Kgs.
Resolution: 5 lbs . Each
Load ability: 1200 lbs .

CDG-100 Curl Diameter Gauge

--- Measure Curl Diameter for Ends

  The “CDG-100 Curl Diameter Gauge” is a Digital gauges for measuring Curl Diameter of ends . It is equipped with a calibration piece. With the Mitutoyo 0.01mm Resolution Digital Indicator.

It is equipped with a digital dial gauge with “reset” and “preset” function, LCD display and data outlet for connecting the unit to a computer via multiplexer, if required.

Technical data (changes reserved):
Resolution: 0, 01 mm
Power supply: Battery , SR-44, approx.5.000 h

CSM-147 Can Seam Micrometers

CSM-147-1; CSM-147-2; CSM-147-3

CSM-147-1; CSM-147-2; CSM-147 can measure the seam thinness and length for straight wall cans.
CSM-147-1can also measure the countersink.
CSM-147-3 is for measuring the seam thickness and length of necked-in cans.
Technical data:
Measure range:
Seam thickness: 0 - 9.00mm ,
Length: 0 - 9.00mm ;
Countersink: 0 - 5.00mm
Resolution: 0.01mm

DHG-300 Digital Can Height Gauge

 

The “DHG-300 Digital Can Height Gauge” can be used to measure the height of beverage, food, and aerosol cans. With the 0.01mm Resolution Digital Indicator.

Technical data (changes reserved):
Measure range:
0 -300mm , DHG-300
0 -600mm , DHG-600
Resolution: 0.01 mm
Accuracy: 0, 02 mm

ECH-d End Curl Height Gauge

The “ ECH-d End Curl Height Gauge” is a Digital gauges for measuring Curl Height of ends . With the Mitutoyo 0.01mm Resolution Digital Indicator. If you purchase the adapter and cable, the instrument can communicate with a computer.

Technical data (changes reserved):
Resolution: 0, 01 mm
Power supply: Battery , SR-44, approx.5.000 h

CSS-100B Anti-noise Seam Saw

“CSS-100B Anti-noise seam saw” is provided with an anti-noise design and a special guide for 2- and 3-piece cans ( 65 mm dia.). Special seam circular saw with double cut for can double seam inspections. The CSS 100B was specially designed for 2- and 3-piece cans. The nitrated blades achieve together with the speed of approx. 1.000 r/min. a very plain cut surface. The seam image on VSM 6A Automatic Seam Computer (Video Seam Monitors), and automatic seam measuring systems gets thereby very clear and improves measurement speed and reliability.

Technical data (changes reserved):
Sample can dia.: 65mm
Sample type : 2- and 3-piece cans.
Saw blades: 80 x 22 x 0, 5 mm , (Part No.: HSS-1-80-5)
Speed: approx. 1.000 r/min.
Power supply: 220
Power: 100W
Dimensions: L380×W240×H 200mm
Weight: 12kg

LSS-100 Low speed Saw

--- rivet quality of the ends

The " LSS-100 Low Speed Saw" is for cut the End rivet to observe and evaluate the rivet profile images of ends. It work with the "Canneed VRM 3A Video Rivet monitor”

The end is cut through the rivet by the LSS-100 Low Speed Saw, the rivet is positioned manually in front of the camera. The rivet profile images display on the display.

Use the “VRM Measuring Software” to measure the rivet quality. It is able to print the rivet profile images and data, convenient for the communication of quality control.

PDG-d Plane depth Gauge (Digital)

The “PDG-d Plane depth Gauge (Digital)” is for measuring the bottom end depth of the cans. The measuring base would be subject to the sample size, so please indicated the end size when purchasing.

To connect the PDG-d with the adapter and cable, all the measurement data can be transferred to the computer or SPC system, so that to avoid recording the data manually.

The “PDG-d Plane depth Gauge (Digital)” consists of Plane depth Gauge and calibration base.

 

Technical data: Measure range: 0 -10mm (changes by order) Resolution: 0.001mm ; Accuracy: ± 0.003mm

PTG -d Digital Plate Thickness Gauge

Measure Thickness of Tinplates

This unit serves for quickly checking the thickness of plates. The sample is presented vertically in this version. It is equipped with a digital dial gauge with "reset" and "preset" function, LCD display and data outlet for connecting the unit to a computer via multiplexer, if required.

Technical data:
Resolution: 0,001 mm
Power supply: Battery , SR-44, approx.5.000 h
Accuracy: 0,003 mm ± 1 digit Data outlet to multiplexer

PTT-200 Pop & Tear Tester

---The most advanced Pop & Tear Tester

PTT-200 Pop & Tear Tester has been developed for testing different kinds of easy open ends.

6 different types of ends: RP / SOT / EO / OVAL / SNAP and ALUFIX.

5 different testing modes: RP / SOT / EO / OVAL and SNAP.

The operators just need to hook the ring and press “test” button, then the PTT-200 will do the test automatically. During the testing process, the microprocessor will monitor and record the max. Pop and Tear force. Equip with different size of the clamps, it is able to test the different size of ends.

Feature:
•  Industry Standard
•  Options of CND_Track analyzing software.
•  Simple operation
•  Rs-232 Communications Capability, can export data to SPC.
•  PLC touch-screen control system, Auto data collection.
•  High accuracy
•  Calibration option, convenience for calibrating.
•  No need the air source

Technical data (Changes reserved): Measuring range : 0-100N Resolution : 0.1 N Interfaces : RS 232C Units: N Power supply: 230V/50Hz Dimension: 850 x 350 x 420 mm Weight: 20kg

Applicable for different kinds of Ends, easy to change the clamps

EO

SOT

RP

OVAL

ALUFIX

SNAP

hook the ring and press “test” button

CND_Track analyzing software

 

 

 

 

 

 

VSM 3A + Automatic Seam Monitor

VSM 3A + Automatic Seam Monitor CSS-200 Seam Saw ( Option )

 

VSM 3A + Automatic Seam Monitor has adopted the advanced optical system and Golden Lens TM video capture device, which ensured the high image definition and the measurement accuracy. The VSM 3A + Automatic Seam Monitor is equipped with the professional seam measuring software CanNeed CND_VSM3.0. The software  also adopted the data base management system, all the measurement data will be restored in the system data base, so that to enhance the software performance and more convenience in data management. The result statistic and result chart has been added in the data base screen for overview and comparison. Meanwhile, the measurement screen has been optimized for a vivid result display. The magnifier option enable users to magnify the testing image for a more accurate line positioning, so that the measurement results are more accurate and reliable.

• Features:
• •  Equipped with Golden Lens TM video capture device which ensured the high image definition ;
• •  Software adopted data base management system, users can review or re-measure the saved projects at any time.
• •  M easuring Items: Seam Length, Body Hook Length, End Hook Length, Overlap, Seam gap, Overlap rate, Body Hook lapping rate, End Hook lapping rate, On-screen Seam Thickness
• •  SPC compatible, use a data adapter to collect the data from Mitutoyo Digital Indicator ( Actual Seam Thickness; Actual countersink )
• •  Measure results can automatically be stored in the Excel file format
• •  Report format can be customized, flexible for different report styles of different companies.
• •  Graph chart statistic function, automatically analyze and compare the measurement results.
• •  Magnifier option enable users to magnify the testing image for a more accurate line positioning;
• •  Measured values are displayed in on-screen and alarm if values are not within specs;
• •  Seam image can be printed, stored;
• •  Provided with calibration piece, calibrate at any time;
• Use the monochromatic source, make it much more durable